‘VICO’ Analog Pirani Gauge is a vacuum measurement instrument designed for use with the thermal conductivity type gauge head (sensor).

 

Specifications:

Measurement: Atm- 0.001 mbar

Units: Mbar

Display: Analog dial meter

Response time: 100 m sec

No. of channels: Two

Input supply (mains): Input AC 230V AC 50Hz

Gauge head (sensor): One or two as ordered

Analog output: 0-10V approx.

 

• Suitable for High Vacuum Metallizing Plants

• Thermal Evaporation Coating Units/ Vacuum Stations

• Sputtering Systems and Vacuum Furnaces

• Continuous Roll Metallizing Plants

• Impregnation Units/ Epoxy Mixing and Casting Units

‘VICO’ Analog Penning Gauge is a vacuum measurement instrument designed with the cold cathode type gauge head (sensor).

 

The model range from 1x10-3 to 10x10-5 mbar (top-scale) and from 2x10-5 to 1x10-6 (bottom-scale). This gauge covers a pressure range of 1x10-3 to 1x10-6 mbar in two ranges with instant range changing provided by a toggle switch.

​

Specifications:

Measurement: 1x10-3 to 1x10-6 mbar

Units: Mbar

Display: Analog dial meter

No. of channels: One 

Input supply (mains): Input AC 230V AC 50Hz

Gauge head (sensor): One 

Analog output: 0-10V approx.

 

• Suitable for High Vacuum Metallizing Plants

• Thermal Evaporation Coating Units/ Vacuum Stations

• Sputtering Systems and Vacuum Furnaces

• Continuous Roll Metallizing Plants

• Impregnation Units/ Epoxy Mixing and Casting Units

‘VICO’ Digital High Pressure Pirani Gauge is a vacuum measurement instrument designed for use with the thermal conductivity type gauge head (sensor). This instrument is having a wide range of applications in High Vacuum Systems where backing vacuum or roughing vacuum needs to be measured. The gauge provides all necessary bridge circuit and signal conditioning, analog output, ADC, digital lineariser, digital display. This model range from 999 to 0.001 m bar.

 

Specifications:

 Power: 230VAC +/- 10%, 50 Hz, 15 watts (approx.)

Fuse: 100 m.a Glass Cartridge 5x20 mm

Dimensions: 91 mmH, 91 mmW, 236 mmD

Front Bezel: 98x98 mm

Thickness: 10 mm

Cut Out Size: 92 mm x 92 mm

Operating Temperature: 0 to 45 degrees C

Pressure Range: 999 mbar to 0.001 mbar

Gauge Head (Sensor): One or Two as required, with KF10 clamp & SS ring + Oring +sensor lead & power chord

Bridge Voltage: -2 VD.C +/- 0.5%

Display: 3 digit LED numeric display with (UR) under range (AT) and (OR) over range (FS)

 

• Suitable for High Vacuum Metallizing Plants

• Thermal Evaporation Coating Units/ Vacuum Stations

• Sputtering Systems and Vacuum Furnaces

• Continuous Roll Metallizing Plants

• Impregnation Units/ Epoxy Mixing and Casting Units

VICO’ Digital Penning Gauge is a vacuum measurement instrument designed with the cold cathode type gauge head (sensor). This provides all necessary circuit and signal conditioning, analog output, ADC, digital lineariser, digital display.

 

This gauge covers a pressure range of 9.9 x10-3 to 1x10-6 mbar

 

Specifications:

Power: 230VAC +/- 10%, 50 Hz, 22 watts (approx.)

Fuse: 500 m.a Glass Cartridge 5x20 mm

Dimensions: 91 mmH x 91 mmW x 236 mmD

Front Bezel: 98x98 mm/ Thickness: 10 mm

Cut Out Size: 92 mm x 92 mm

Operating Temperature: 0 to 45 degrees C

Pressure Range: 9.9 x10-3 mbar to 1x10-6 mbar

Gauge Head (Sensor): One No. with KF25 clamp & SS ring + Oring + sensor lead & power chord

Output Voltage (Sensor): 220 KV DC +/- 10%

Sensor Type: Cold Cathode Ionization (Penning) Type Head, One

Display: 3 digit LED numeric display with (UR) under range (above 99 x 10-3 mbar) and (OR) over range (below 1.0 x 10-6 mbar)

 

• Suitable for High Vacuum Metallizing Plants

• Thermal Evaporation Coating Units/ Vacuum Stations

• Sputtering Systems and Vacuum Furnaces

• Continuous Roll Metallizing Plants

• Impregnation Units/ Epoxy Mixing and Casting Units

Film thickness is the depth of the coating applied.

Thin-film thickness monitors, deposition rate controllers, are instruments used in high and ultra-high vacuum systems. A thickness monitor measures how much material deposited on its sensor.

 

Specifications:

Measurement Range: Transducer Limited, Typically 5000 microgram/sq.cm, as much as 20000 microgram/sq.cm for well behaved materials (1.0 microgram/sq.cm = 37 Ang AL)

Rate Display: 3 digits LED Auto ranging from 00.0 to 99. Ang/sec

Thickness Display: 4 digits LED Auto ranging from 0.000 to 999.9 K Ang

Undated Rate: Automatically Varied-.4to r updates/sec

Static Thickness Resolution: 1 Ang at minimum update rate

Input Parameter: Tooling factor, Density & Acoustic impedance inputs allow readout directly in Angstroms

Film No.: Allows input parameters for 1 to 100 films

Tooling Factor: 1.0 to 999.9 %

Film density: 0.800 to 99.99 gm/cubic sec

Film Acoustic impedance shutter control: 5.000 to 99.99 x 10 gm/cm sec, Dedicated replay. Internal 3 Amp fuse protection, Two replays

Thickness Set Point: 0.000 to 999.9 K Ang, Shutter closes when displayed thickness equals or exceeds set point

Start Control: Zero thickness and opens shutter

Stop Control: Close shutter

Shutter Position indicator: LED on indicates shutter replays activated

Crystal Compatibility: 6 MHz

Crystal Test Display: 0 to +5 +/- .25 V full scale, Corresponding to last 2 or 3 digits of selected display

Output Control: Rate or Thickness select Decade select for conversion of last 2 or 3 digits of display. Fill scale and zero scale output useful in calibrating recording equipment

The International Standards Organization has defined the interface dimensions of ISO-KF vacuum flanges allowing the interchanging of components that conform to the ISO-KF standard. Since component dimensions are standardized, elbows, tees, crosses or valves for a given flange size can be interchanged. 

 

ISO-KF vacuum clamps provide the sealing force to fully compress the O-ring for a vacuum seal, and mechanical force to hold the two flange faces together. 

 

• The KF Clamps are available in standard KF 10/16/25/40 and KF 50 size.

• The clamp is Aluminium die cast with stainless steel centering ring and Oring. Stainless steel clamps can also be made as per customer’s request.

• The material used is SS grade-304 for all flanges, weld stub, blanks, elbow/Tee and cross and reducers etc.

• Stainless steel flexible Bellows can be made as per customer’s requirement with specific flange end-connections and length.

• ConFlat (CF) fittings or flanges using metal seals and copper gasket (OFHC) and Needle valves and bigger length weld stubs are available as per custom requirements.